0
Owner's of the Onkyo Stereo Receiver TX-NR3008 gave it a score of 0 out of 5. Here's how the scores stacked up:
51
En
■ Speaker Impedance
`4ohms:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
`6ohms
:
Select if the impedances of all speakers are between
6 and 16 ohms.
Note
• When bridging is used, “Speaker Impedance” setting is fixed at
“8ohms”.
■ Speakers Type(Front A)
`Normal
:
Select this if you’ve connected your front speakers A
normally.
`Bi-Amp:
Select this if you’ve connected your front speakers A
for bi-amped operation. The Bi AMP indicator will
light (➔ 9).
`BTL:
Select this if you’ve connected your front speakers A
for bridged operation. The BTL indicator will light
(➔ 9).
Note
•“Bi-Amp” and “BTL” cannot be selected if “Speakers
Type(Front B)” is set to “Bi-Amp” or “BTL”.
• Surround back speakers and Powered Zone 3 cannot be used if
you select “Bi-Amp” or “BTL”.
•“Speakers Type(Front A)” is set to “Normal” if the “Front
High + Front Wide” setting is set to “Ye s ”.
■ Speakers Type(Front B)
`Not Use
:
Select this if you’re not using speakers B.
`Normal:
Select this if you’ve connected your front speakers B
normally.
`Bi-Amp:
Select this if you’ve connected your front speakers B
for bi-amped operation. The Bi AMP indicator will
light (➔ 9).
`BTL:
Select this if you’ve connected your front speakers B
for bridged operation. The BTL indicator will light
(➔ 9).
Note
•“Bi-Amp” and “BTL” cannot be selected if “Speakers
Type(Front A)” is set to “Bi-Amp” or “BTL”.
• Front high speakers, front wide speakers and Powered Zone 2
cannot be used if you select other than “Not Use”.
• Surround back speakers and Powered Zone 3 cannot be used if
you select “Bi-Amp” or “BTL”.
• This setting cannot be used if “Front High + Front Wide” set-
ting is set to “Ye s”.
■ Powered Zone 2, Powered Zone 3
See “Setting the Powered Zone 2/3” (➔ 82).
■ Front High + Front Wide
`Ye s:
Front High + Front Wide on.
`No
:
Front High + Front Wide off.
Listening mode that make use of “Front High + Front
Wide” setting is as follows;
Audyssey DSX (PLII/Neo:6 + Audyssey DSX included),
Orchestra, Unplugged, Studio-Mix, TV Logic, Game-
RPG, Game-Action, Game-Rock, Game-Sports, All Ch
Stereo, Full Mono.
Note
• When you have selected “Yes”,
–the “Surround Back” setting is set to “None”.
–the “Front High” or “Front Wide” setting is set to
“80Hz(THX)” if set to “None”.
•The “Front High + Front Wide” setting cannot be used in either
of the following cases;
–“Bi-Amp” or “BTL” is being used.
– Powered Zone 2/3 are being used.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
You can set the crossover frequencies, distances, and lev-
els of the front speakers A and front speakers B indepen-
dently. The other speakers (i.e., subwoofer, center,
surround, and surround back) use the same crossover fre-
quencies, distances, and levels for Speakers A and Speak-
ers B. Specify “Full Band” for speakers that can output
low frequency bass sounds adequately, for example,
speakers with a good sized woofer. For smaller speakers,
specify a crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies.
If you set up your speakers using Audyssey MultEQ XT32
Room Correction and Speaker Setup, please make sure
manually that any THX speakers are set to “80Hz(THX)”
crossover.
■ Subwoofer
`1ch:
Audio signal is outputted from SW1 jack only.
`2ch
:
Audio signal is outputted from SW1 and SW2
jacks.
`No:
Select if no subwoofer is connected.
This setting is set automatically by
Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup function (➔ 32). For Speakers B, you
need to change the settings manually.
Find Your Products By Category
Please Login
