0
Owner's of the Onkyo Stereo Receiver TX-NR3008 gave it a score of 0 out of 5. Here's how the scores stacked up:
50
En
Digital Audio Input
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example, if
you connect your CD player to the OPTICAL IN 1, you
must assign “OPT 1” to the “TV/CD” input selector.
Here are the default assignments.
■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, TAPE,
TV/CD, PHONO, PORT
`COAX 1, COAX 2, COAX 3, OPT 1, OPT 2,
OPT 3 (TX-NR5008):
Select a corresponding digital audio input that the
component has been connected.
`-----:
Select if the component is connected to an analog
audio input.
•“AUX” is used only for input from the front panel.
Note
• When an HDMI IN is assigned to an input selector in “HDMI
Input” (➔ 48), the same HDMI IN will be set as a priority in this
assignment. In this case, if you want to use the coaxial or optical
audio input, make the selection in the “Audio Selector” in the
Home menu (➔ 68).
• Available sampling rate for PCM signals from a digital input
(optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.
•“TUNER” selector cannot be assigned and is fixed at the
“-----” option.
• If you connect a component (such as UP-A1 Dock that seated
iPod) to the UNIVERSAL PORT jack, you cannot assign any
input to “PORT” selector.
Analog Audio Input
If you connect a component to the AV receiver’s analog
multichannel input, you must assign that input to an input
selector. For example, if you connect your Blu-ray Disc/
DVD player to the MULTI CH input, you must assign it to
the “BD/DVD” input selector.
■ Multich
`BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX,
TAPE, TV/CD, PHONO
You can assign the multichannel input to the input
selectors.
`-----:
If you don’t want to assign the multichannel input,
set to “-----”.
Note
• To listen to the component connected to the multichannel input,
make the selection in the “Audio Selector” in the Home menu
(➔ 68).
■ Subwoofer Input Sensitivity
`0dB
to 15dB in 5 dB step.
Some DVD players output the LFE channel from their
analog subwoofer output at 15 dB higher than normal.
With this setting, you can change the AV receiver’s sub-
woofer sensitivity to match your DVD player.
Note
• This setting only affects signals connected to the AV receiver’s
multichannel input SUBWOOFER jack.
• If you find that your subwoofer is too loud, try the 10 dB or
15 dB setting.
Main menu Speaker Setup
Here you can check the settings made by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup, or set them manually, which is useful if you change
one of the connected speakers after using
Audyssey MultEQ XT32 Room Correction and Speaker
Setup.
Press RECEIVER and use SP LAYOUT on the remote
controller to select Speakers A or Speakers B.
Note
• These settings are disabled when:
– a pair of headphones is connected, or
–the “Audio TV Out” setting is set to “On” (➔ 64) and an
input selector other than HDMI is selected.
Speaker Settings
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
To use bi-amping or bridging, you must change the
“Speakers Type(Front A)” or “Speakers Type(Front
B)” setting (➔ 51). For details on speaker wire connec-
tion, see “Connecting the AV Receiver” (➔ 17 to 19).
Note
• When bridging is used, the AV receiver is able to drive up to 7.2
speakers in the main room.
• When bi-amping is used, the AV receiver is able to drive up to
7.2 speakers in the main room.
• Before you change these settings, turn down the volume.
Input selector Default assignment
BD/DVD COAX 1
VCR/DVR COAX 2
CBL/SAT COAX 3
GAME OPT 1
PC -----
AUX FRONT (Fixed)
TAPE -----
TUNER ----- (Fixed)
TV/CD OPT 2
PHONO -----
PORT -----
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup (➔ 32). For Speakers B, you need to
change the settings manually.
If you change these settings, you must run
Audyssey MultEQ XT32 Room Correction and
Speaker Setup again (➔ 32).
Find Your Products By Category
Please Login
