0
Owner's of the Onkyo Stereo Receiver AV Receiver gave it a score of 0 out of 5. Here's how the scores stacked up:
Advanced Operations
En-66
Main Menu Speaker Setup
Here you can check the settings made by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function, or set them manually, which is useful if
you change one of the connected speakers after using
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function.
Press RECEIVER and use SP on the remote controller to
select Speakers A or Speakers B. For details on SP, see
“Selecting Speaker Layout” (➔ page 55).
Note
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
–the “Audio TV Out” setting is set to “On” (➔ page 84).
–“HDMI Control(RIHD)” is set to “On” (➔ page 83) and
you’re listening through your TV speakers.
Speaker Settings
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
“Speakers Type(Front A)” or “Speakers
Type(Front B)” setting. For details on speaker wire
connection, see “Bi-amping the Front Speakers”
(➔ page 18). When connecting speakers without
crossover network, you need to change the “Speakers
Type(Front A)” or “Speakers Type(Front B)” setting
beforehand. For details on connection, refer to “Using
Speakers Without Crossover Network” (➔ page 18).
Note
• When bi-amping is used, the AV receiver is able to drive up to 7.2
speakers in the main room.
• Before you change these settings, turn down the volume.
■ Speaker Impedance
`4ohms:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
`6ohms
:
Select if the impedances of all speakers are between 6
and 16 ohms.
■ Speakers Type(Front A)
`Normal
:
Select this if you’ve connected your front speakers A
normally.
`Bi-Amp:
Select this if you’ve bi-amped your front speakers A.
`Digital Crossover:
Select this if you’re using speakers without crossover
network.
■ Speakers Type(Front B)
`No
:
Select this if you’re not using speakers B.
`Normal:
Select this if you’ve connected your front speakers B
normally.
`Bi-Amp:
Select this if you’ve bi-amped your front speakers B.
`Digital Crossover:
Select this if you’re using speakers without crossover
network.
Tip
• If “Speakers Type(Front A)” or “Speakers Type(Front B)” is
set to “Digital Crossover”, a confirmation screen appears. Select
“Next (2-7. Digital Processing Crossover Network)” to display
the screen for Digital Processing Crossover Network
(➔ page 71). Continue with the settings.
■ Powered Zone 2, Powered Zone 3
`No
`Yes:
Zone 2/3 speakers can be used. (Powered Zone 2/3
enabled).
■ 11ch Playback
`No
`Yes
For 11.2-channel playback, set this setting to “Yes”. If you
select front wide speakers setting in Speaker Configuration
is set to “None”, it will be automatically switched to
“80Hz (THX)”.
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup function (➔ page 42). For Speakers B,
you need to change the settings manually.
1 2 3 4 5
“Setup”
If you change these settings, you must run
Audyssey MultEQ XT32 Room Correction and
Speaker Setup again (➔ page 42).
To be continued
Find Your Products By Category
Please Login
