Onkyo Stereo Receiver AV Receiver User Manual

0

Out of 0 Ratings

Owner's of the Onkyo Stereo Receiver AV Receiver gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 168
 
Turning On & Basic Operations
En-45
Changing the Speaker Setup Manually
You can manually make changes to the settings found
during Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup.
See also:
• “Speaker Configuration” (➔ page 67)
• “Speaker Distance” (➔ page 69)
• “Level Calibration” (➔ page 69)
• “Equalizer Settings” (➔ page 70)
Note
• Please note that THX recommends any THX main speakers be set
to “80Hz(THX)”. If you set up your speakers using
Audyssey MultEQ XT32 Room Correction and Speaker Setup,
please make sure manually that any THX speakers are set to
“80Hz(THX)” crossover (➔ page 67).
• Sometimes due to the electrical complexities of subwoofers and
the interaction with the room, THX recommends setting the level
and the distance of the subwoofer manually.
• Sometimes due to interaction with the room, you may notice
irregular results when setting the level and/or distance of the main
speakers. If this happens, THX recommends setting them
manually.
Using a Powered Subwoofer
If you’re using a powered subwoofer and it outputs very
low-frequency sound at a low volume level, it may not be
detected by Audyssey MultEQ XT32 Room Correction
and Speaker Setup.
If the “Subwoofer” appears on the “Review Speaker
Configuration” screen as “No”, increase the subwoofer’s
volume to the half-way point, set it to its highest crossover
frequency, and then try running Audyssey MultEQ XT32
Room Correction and Speaker Setup again. Note that if the
volume is set too high and the sound distorts, detection
issues may occur, so use an appropriate volume level. If the
subwoofer has a low-pass filter switch, set it to Off or
Direct. Refer to your subwoofer’s instruction manual for
details.
Selecting Listening Modes
See “About Listening Modes” for detailed information
about the listening modes (➔ page 46).
■ Listening Mode Buttons
MOVIE/TV button
This button selects the listening modes intended for use
with movies and TV.
MUSIC button
This button selects the listening modes intended for use
with music.
GAME button
This button selects the listening modes intended for use
with video games.
THX button
This button selects the THX listening modes.
PURE AUDIO button and indicator
This button selects the Pure Audio listening mode.
When this mode is selected, the AV receiver’s display and
analog video circuitry are turned off. Only video signals
input through HDMI input can be output from the HDMI
output. The indicator lights when this mode is selected.
Pressing this button again will select the previous listening
mode.
Using the Listening Modes
GAME
THX
MOVIE/TV
MUSIC
Press RECEIVER first.
PURE AUDIO MOVIE/TV, MUSIC, GAME, THX
• The Dolby Digital and DTS listening modes can only be
selected if your Blu-ray Disc/DVD player is connected to
the AV receiver with a digital audio connection (coaxial,
optical, or HDMI).
• The listening modes you can select depends on the format
of the input signal. To check the format, see “Displaying
Source Information” (➔ page 54).
• While a pair of headphones is connected, you can select the
following listening modes: Pure Audio, Mono, Direct, and
Stereo.

   Find Your Products By Category