4.0
Owner's of the Onkyo Stereo Receiver AV RECEIVER gave it a score of 4.0 out of 5. Here's how the scores stacked up:
Appendix
En-75
■ There’s no picture
■ There’s no picture from a source connected to
an HDMI IN
■ The on-screen menus don’t appear
■ The on-screen display does not appear
■ Reception is noisy, FM stereo reception is noisy,
or the FM STEREO indicator doesn’t light
■ The remote controller doesn’t work
■ Can’t control other components
Video
Make sure that all video connecting plugs are pushed
in all the way.
14
Make sure that each video component is properly
connected.
15, 16
If your TV is connected to the HDMI output(s), select
“-----” in the “HDMI Input” setup to watch
composite video, and component video sources.
48
If the video source is connected to a component video
input, you must assign that input to an input selector,
and your TV must be connected to either the HDMI
output(s) or COMPONENT VIDEO OUT.
16, 49
If the video source is connected to a composite video
input, your TV must be connected to the HDMI
output(s) or the corresponding composite video
output.
16
If the video source is connected to an HDMI input,
you must assign that input to an input selector, and
your TV must be connected to the HDMI output(s).
15, 48
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
—
Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not guaranteed.
88
When the resolution is set to any resolution not
supported by the TV, no video is output from the
HDMI outputs.
48
If the message “Resolution Error” appears on the
AV receiver’s display, this indicates that your TV
does not support the current video resolution and you
need to select another resolution on your DVD
player.
—
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
—
When the AV receiver is not connected to a TV via
HDMI OUT MAIN, on-screen menus are not
displayed.
—
Depending on the input signal, the on-screen display
may not appear when the input signal from HDMI IN
is output to a device connected to HDMI OUT MAIN.
43
Tuner
Relocate your antenna. —
Move the AV receiver away from your TV or
computer.
—
Listen to the station in mono. 30
When listening to an AM station, operating the
remote controller may cause noise.
—
Passing cars and airplanes can cause interference. —
Concrete walls weaken radio signals. —
If nothing improves the reception, install an outdoor
antenna.
—
Remote Controller
Before operating this unit, be sure to press
RECEIVER.
—
Make sure that the batteries are installed with the
correct polarity.
4
Install new batteries. Don’t mix different types of
batteries, or old and new batteries.
4
Make sure that the remote controller is not too far
away from the AV receiver, and that there’s no
obstruction between the remote controller and the AV
receiver’s remote control sensor.
4
Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
—
If the AV receiver is installed in a rack or cabinet
with colored-glass doors, the remote controller may
not work reliably when the doors are closed.
—
Make sure you’ve selected the correct remote
controller mode.
10, 70
When using the remote controller to control other
manufacturers’ AV components, some buttons may
not work as expected.
—
Make sure you’ve entered the correct remote control
code.
69
Make sure to set the same ID on both the AV receiver
and remote controller.
63
If it’s an Onkyo component, make sure that the
cable and analog audio cable are connected properly.
Connecting only an cable won’t be enough.
17
Make sure you’ve selected the correct remote
controller mode.
10, 70
If you’ve connected an cassette tape deck to the
TV/CD IN jack, or an RI Dock to the TV/CD IN or
GAME IN jacks, for the remote controller to work
properly, you must set the input display
appropriately.
41
If you cannot operate it, you will need to enter the
appropriate remote control code.
68
To control another manufacturer’s component, point
the remote controller at that component.
69
To control an Onkyo component that’s connected via
, point the remote controller at the AV receiver.
Be sure to enter the appropriate remote control code
first.
70
To control an Onkyo component that’s not connected
via , point the remote controller at the component.
Be sure to enter the appropriate remote control code
first.
70
The entered remote control code may not be correct.
If more than one code is listed, try each one.
—
Find Your Products By Category
Please Login
