0
Owner's of the Onkyo Stereo Receiver Onkyo HTS3500 5.1 Channel Home Theater System gave it a score of 0 out of 5. Here's how the scores stacked up:
Advanced Operations
En-46
■ Audio Return Ch (ARC)
`Off
`Auto:
The audio signal from your TV tuner can be sent to
the HDMI OUT of the AV receiver.
The audio return channel (ARC) function allows an ARC
capable TV to send the audio stream to the HDMI OUT of
the AV receiver. To use this function, you must select the
TV/CD input selector and your TV must be ARC capable.
Note
• This setting is fixed to “----” when the “HDMI Ctrl (RIHD)”
setting is set to “Off”.
• This setting is set to “Auto” automatically when the “HDMI Ctrl
(RIHD)” setting is set to “On” for the first time.
• If you set “Audio Return Ch” to “Auto”, the “Audio Selector”
settings of the TV/CD input selector will be automatically
switched to “ARC” (➔ page 43).
■ LipSync
`Off
`On
This function allows the AV receiver to automatically
correct any delay between the video and the audio, based
on the data from the connected monitor.
Note
• This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
You can change various audio settings from the Home
menu (➔ page 33).
Note
• These settings are not available in either of the following cases:
–The “Audio TV Out” setting is set to “On” (➔ page 45).
–“HDMI Ctrl (RIHD)” is set to “On” (➔ page 45) and you’re
listening through your TV speakers.
Tone Control
■ Bass
`–10 dB to 0dB
to +10 dB in 2 dB steps
You can boost or cut low-frequency sounds output
from the front speakers.
■ Treble
`–10 dB to 0dB
to +10 dB in 2 dB steps
You can boost or cut high-frequency sounds output
from the front speakers.
You can adjust the bass and treble for Speakers A and B
front speakers, except when the Direct listening mode is
selected.
Operating on the remote controller directly
Tip
• Alternatively, you can use the AV receiver’s TONE and –/+.
Speaker Levels
■ Subwoofer Level
`–15 dB to 0dB
to +12 dB in 1 dB steps
Operating on the remote controller directly
Tip
• Alternatively, you can use the AV receiver’s TONE and –/+.
■ Center Level
`–12 dB to 0dB
to +12 dB in 1 dB steps
You can adjust the volume of each speaker while listening
to an input source.
These temporary adjustments are cancelled when the AV
receiver is set to standby. To save the setting you made
here, go to “Level Cal (Level Calibration)” (➔ page 41)
before setting the AV receiver to standby.
Note
• These settings cannot be calibrated in either of the following
cases:
– A pair of headphones is connected.
– The AV receiver is muted.
• Speakers that are set to “No” or “None” in the “Sp Config
(Speaker Configuration)” (➔ page 40) cannot be adjusted.
After changing the settings of the “HDMI Ctrl
(RIHD)”, “HDMI Through” or “Audio Return Ch”
turn off the power on all connected pieces of equipment
and then turn them on again. Refer to the user’s manuals
for all connected pieces of equipment.
Using the Audio Settings
1
Press RECEIVER followed by HOME.
2
Use / and ENTER to select “Audio”, and then
use / / / to make the desired selection.
1
Press RECEIVER once followed by TONE
repeatedly to select either “Bass” or “Treble”.
2
Use – and + to adjust.
1
Press RECEIVER once followed by TONE
repeatedly to select “Subwoofer”.
2
Use – and + to adjust.
Find Your Products By Category
Please Login
